Thermal Negative Printing Plate Development On Press
Processless CTP Plate
Model: ECOO-G
EcooGraphix ECOO-G is a new, environmentally friendly, development on press CTP plate.
It can be run directly on a printing press after imaging, without a need for chemical processing.
Characteristics
ECOO-G is double layer, and the emulsion layer will not dissolve into water, so it will not integrate into fountain solution; while the protection layer is well water-soluble, and it will be easy dissolved into the fountain solution.
Specification
| Model | ECOO-G |
| Plate Type | Thermal-negative type |
| Application | High grade commercial and newspaper printing |
| Substrate | Electrolyte Graining and Anodized AL substrate |
| Thickness | 0.15mm / 0.30mm |
| Maximum short grain width | Maximum width 1280 mm |
| Spectrum scope | 800-850 nm |
| Photosensitive wave length | 830 nm |
| Platesetter | Various dominant thermal platesetters in the market |
| Coating color | Grey |
| Low-energy imaging | 130-150 mj/ cm² |
| The period of latent image stabilization | ≤ 7 days |
| Recommended screen method | 1-99% @200 LPI AM or 20μm FM or mixture |
| The paper number of start-up | < 50 sheets |
| Safety light | 4 hours under yellow light; 1 hour under fluorescent l Direct exposure under natural light is safe but not recommended. |
| Processing | Without processing, directly on press |
| Run Length | 100,000 impressions; Actual run length depends on printing conditions |
| Shelf life | 12 months under recommended condition |
| Transportation | Packed in seal and stored by means of prevention from light, moisture, overheat and high humidity |
| Storage | Recommended condition: 18ºC-24ºC, 40%-50% RH. |
Applied parameters in Imaging device
| CTP model Data | Kodak trendsetters | LOTTEM 400(TH1.7) | MAGNUS 400 | Screen 8600S |
| Laser power | 15-17W | 300-320mw | 19.5-21.5W | 80-90 % |
| Drum speed | 250-300rpm | 850-900rpm | 400-450rpm | 800-900rpm |
| Resolution | Customized | Customized | Customized | Customized |
| Parameter that need set up | Focus/ Zoom | Focus/ Zoom | Focus/ Zoom | Focus/ Zoom |
*Note: Higher exposure energy will make the image contrast more clear, and benefit to the plate run length;
while over high/low exposure energy will affect the image quality negatively.
ECOO-G Processless CTP plate Video: https://youtu.be/LLqNaY1ivcI
Model
ECOO-G
Plate Type
Thermal-negative type
Application
High grade commercial and newspaper printing
Substrate
Electrolyte Graining and Anodized AL substrate
Thickness
0.15mm / 0.30mm
Maximum short grain width
Maximum width 1280 mm
Spectrum scope
800-850 nm
Photosensitive wave length
830 nm
Platesetter
Various dominant thermal platesetters in the market
Coating color
Grey
Low-energy imaging
130-150 mj/ cm²
The period of latent image stabilization
≤ 7 days
Recommended screen method
1-99% @200 LPI AM or 20μm FM or mixture
The paper number of start-up
< 50 sheets
Safety light
4 hours under yellow light; 1 hour under fluorescent l Direct exposure under natural light is safe but not recommended.
Processing
Without processing, directly on press
Run Length
100,000 impressions; Actual run length depends on printing conditions
Shelf life
12 months under recommended condition
Transportation
Packed in seal and stored by means of prevention from light, moisture, overheat and high humidity
Storage
Recommended condition: 18ºC-24ºC, 40%-50% RH.
Application
Recommended application to press procedures of ECOO-G:
1. Clean all the inks on the blanket;
2. Start the press machine, apply the water roller, run 30-40 seconds;
3. Apply the ink rollers 20-30 seconds;
4. Apply the paper and start print.
Remark: If operate step 2 and 3 longer, paper will be wasted less.
Producing and Packing
From producing to delivery, we make every details very carefully to guarantee the good product quality and service to customers.
Certifications
FAQ
Q1: Can I get the sample ?
A: We are very glad to provide some sample for you to test.
We usually provide 5-15 pieces plates for free, but sincerely hope to get your kind support for the air courier freight.
This cost can be returned to you in your first order.
Q2: What is the cost for the CTP plate sample freight ?
A: The air freight depends on the packing size and weight, and the delivery destination.
Or you can arrange the pick-up service from your local agent.
Q3: How long can the sample be ready ?
A: It usually takes about 3 days to prepare the sample.
Q4: Can I visit your factory ?
A: You are warmly welcome to visit our factory! Our company is in Hangzhou city,
which is about 1.5 hours by train from Shanghai.
Q5: How many Square Meters CTP plates can feed one 20' container ?
A: About 20000-25000SQM.
Q6: Can I take my own brand and label on the packing ?
A: Yes, we can provide the OEM with the customer's brand and label.
