Product Description:SS-WD6000 Glass&Glazing Silicone Sealant is a premium 100% silicone sealant with exceptional adhesion and flexibility. This sealant offers 40% joint movement capability and can withstand extreme expansion or contraction associated with wide temperature fluctuations. Ideal for a number of highly demanding exterior and interior projects, this durable sealant can be rain-ready in as little as 30 minutes, is resistant to UV degradation and has lifetime mold-free product protection. SS-WD6000 Glass&Glazing Silicone Sealant's airtight and permanently waterproof seal helps keep weather out and reduce energy consumption. Backed by a lifetime guarantee.
Product Attributes:
• Meets ASTM C-920-01& GB/T14683-2017
• Resist mold with 10-year mold-free product protection
• 30-minute rain-ready
• 100% silicone is 100% waterproof
• Stronger adhesion than SS-BK5500
• Will not discolor most high-end metal finishes such as chrome, bronze and nickel
• Neutral cure with low odor
• Permanently flexible
• Shrink-proof & crack-proof
• Excellent adhesion for wet and dry applications(5)
• Freeze/thaw stability
• Non-paintable
Limitations(should not be considered):
• For structural repairs
• For use underwater or in other applications where the product will be in continuous contact with water
• For use in food contact applications
• When painting of the cured sealant is desired
• For use on aquariums
• For use on surfaces with special coatings, such as mirrors, without approval of the article's manufacturer
• Under exceedingly hot or cold conditions (see Sealant Application section for additional information)
• On frozen or contaminated surfaces
• On excessively basic or acidic substrates
• For use on surfaces that are above 40ºC
Application
Packaging:
Typical Properities Information-Supplied
| Density | g/ml | 1.51±0.02 | Test Method |
| VOC | g/L | 20~35 | |
| Flow (sag or slump) | mm | 0 | |
| Working Life(Tooling time) | minutes | 5~10 | |
| Odo | / | Light | |
| Extrusion Rate Skin Time | sminutes | 310~30 | |
| Tack-free Time(@23ºC,50%RH) | minutes | 10~20 | ASTM C679 |
| Curing time (5mm) | Hours | ≤24 | ASTM C679 |
| Durometer Hardness, Shore A | Points | 15 | Test Method |
| Tensile bonding strength | psi | 227 | ASTM D2240 |
| Elongation at Maximum Tensile strength | % | 353 | ASTM D412 |
| Joint Movement Capability | ±30% | ASTM C719 | |
| Specific Gravity | 1.00 | ||
| Service Temperature | ºC | -50~+150 | |
| Weathering&U.V. Resistance | Excellent | 12 years study | |
| Full Cure Time | Hours | 72 | |
Surface Preparation:
• Surfaces must be clean, dry and sound prior to application of the sealant. All contaminants, impurities, or other adhesion inhibitors (such as moisture/frost, oils, old sealants, soaps and other surface treatments, etc.) must be removed from the surfaces to which the sealant is intended to adhere.
• For cleaning, a solvent-dampened clean rag usually produces the desired result. IPA is a commonly used solvent and has proven useful for most non-porous substrates. When handling solvents, refer to manufacturer's SDS for information on handling, safety and personal protective equipment.
• Architectural coatings, paints and plastics should be cleaned with a solvent approved by the manufacturer of the product or which does not harm or alter the finish.
• Since porous materials can absorb and retain moisture, it is important to confirm that substrates are dry prior to application of the sealant.
• Cleaning of surfaces should be done within 1 to 2 hours of when the sealant is to be applied.
Instructions:
1. Remove dirt, grease, moisture, soap residue & old caulk from area to be sealed.
2. Cut nozzle to obtain desired bead size.
3. Using caulk gun, apply sealant into gap. Smooth the sealant into gap.
4. Wipe hands & tools thoroughly before washing.
5. Allow a minimum of 30 minutes before exposing sealant to water.
Sealant Application:
• Apply sealant in a continuous operation applying a positive pressure adequate to properly fill and seal the seam, cavity or joint.
• Tool or strike the sealant with a concave tool, applying light pressure to spread the material against the joint surfaces to ensure a void-free application.
• When tooling, use care not to spread the sealant over the face of the substrates adjacent to the joint or masking as the silicone can be extremely difficult to remove on rough or porous substrates. Excess sealant should be cleaned from glass, metal and plastic surfaces while still uncured. On porous surfaces the excess sealant should be allowed to progress through the initial cure or set-up. It should then be removed by abrasion or other mechanical means.
• If sealant is applied when the temperature is below 32°F (4°C) or if frost or moisture is present on the surfaces to be sealed, the rate of cure will slow. For standard cure speed, apply in temperatures above 32°F(4°C).
• The cure rate of this product is dependent upon temperature and the availability of atmospheric moisture. Under average conditions (relative humidity of 50 ±5% at an air temperature of 73.4 ±2°F [23 ±1°C]) this material can attain a cured thickness of 2-3 mm per 24 hours (assuming ample access to atmospheric moisture). As temperature decreases, the cure rate slows down (and vice versa). Low moisture environments will also reduce the cure rate. Near-confined spaces, which limit the overall access to atmospheric moisture, will cure only from that surface which has access to the atmosphere.
Note:
• This material requires atmospheric moisture to cure from paste to rubber and may not attain its listed final cured rubber properties when used in designs or applications where the silicone is encapsulated and without access to atmospheric moisture.
• Some materials that bleed plasticizers or oils can cause a discoloration on the surface of sealants. When sealing to or over items such as: rubberized gaskets, bituminous based materials, butyl or oil-based products, oily woods, tapes, etc., compatibility testing prior to use is recommended.
• Silicone materials are hydrophobic in nature and if inadvertently over-applied onto adjacent joint surfaces (even if removed immediately), can create a waterproofing effect of a substrate when the substrate is wet. See section on Masking
Quality Control Equipment
Company ProfileAbout us:
Beijing Sarlsson New material Co,.Ltd. was established in the year of 2000, which is specialized on designing, developing, manufacturing and marketing stone glue products. Our head company was situated in Daxing Industrial Zone of Beijing with predominant geological location and strong research capability. We are the top 5 largest manufacturer of stone glue in China with extensive scientific researching partner, senior expert and wide sale channels. We establish our branch factory in Shanghai and Bengbu successively with total area of 80,000 square meters and annual production ability of 800,000 metric tons.
Our aim is to be the professional construction adhesive manufacturer and satisfy every customer's requirements by supplying the high quality products with competitive price. Our Company mainly produces the marble adhesive, epoxy AB adhesive, fast-curing AB adhesive, anchor adhesive, high strength net stone glue, neutral silicone sealant. We have 9 mark brands in domestic market. Each brand has one sole distributor in one city. Our exporting brand for oversea market is SARLSSON. Our products have reached the international advanced level and have high reputation either in domestic or oversea market. Our products have been exported to Southeast Asia, European, South American, Mideast, Africa market, etc.
We are to build the largest stone adhesive manufactory with leading technology innovation, highly effective branding, rigorous practical work style, scientific and standard management. We will adhere to the concept of respect, integrity, responsibility, diligence and innovation to be conscience enterprises in China.
Welcome customers at home and abroad to visit our factory and negotiate business.
260 workers
80,000sqm workshop
R&D:10 members
12 years export experience
ISO9001&ISO14001
GB/T14683-2017
ASTM C 920-01
Annual Production:800,000 tons
Certificates&Patents
Global Business Scope
Successful Case
Exhibition
FAQ:
1.Are you manufacturer?
Yes. Our company Sarlsson is the top 5 marble glue, Epoxy ab adhesive and Silicone Sealant manufacturer in Asia .
Sarlsson with 19 years experience in this industry, we have served clients from more than 100 countries. Sarlsson is well- known for its quality and our team win clients' trust by honesty and down to earth business style.
2.How long can I get a quote
The quotation can be provided not longer than 24 hours on condition that we know all detailed requirements.
3.Do you accept Private Label!?
Yes. We can do OEM for customers.
4.Can I get a sample before order?
Of course. Generally, we provide 1-3 pieces free samples .
5.How long you will finish my order?
It is depend on your order quantity. Generally, the 20GP container delivery time about 2 weeks .
6.How can you guarantee the quality?
A: We have rigorous quality test system, from raw materials to finished products, the materials must be checked and signed by QC colleagues.
7.How to find the suitable sealants?
Please let me know your application purpose, substrate, application method and all your requirements.
